0xdroid起動ログ

0xdroid donutの、USBにマウスとカメラを挿した状態での起動ログ。
エラーが出たときの比較のため。

Texas Instruments X-Loader 1.4.2 (Feb 19 2009 - 12:01:24)
Reading boot sector
Loading u-boot.bin from nand
Skipped bad block at 0xe0000

U-Boot 2009.11 (Feb 23 2010 - 15:33:48)

OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 256 MB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Board revision C4
Die ID #2ae6000400000000040365fa13020015
Hit any key to stop autoboot: 0
mmc1 is available
reading uImage

1691132 bytes read
## Booting kernel from Legacy Image at 80000000 ...
Image Name: Linux-2.6.29-omap1-00048-ge749c1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1691068 Bytes = 1.6 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.29-omap1-00048-ge749c1f (itog@itog-ubuntu) (gcc version 4.4.10
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OMAP3 Beagle Board
Memory policy: ECC disabled, Data cache writeback
OMAP3430 ES3.1
SRAM: Mapped pa 0x40200000 to va 0xe3000000 size: 0x100000
Reserving 12582912 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: androidboot.console=ttyS2 console=ttyS2,115200n8 console=tt
Unknown boot option `androidboot.console=ttyS2': ignoring
Clocking rate (Crystal/DPLL/ARM core): 26.0/332/720 MHz
Reprogramming SDRC
GPMC revision 5.0
IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP34xx GPIO hardware version 2.5
PID hash table entries: 1024 (order: 10, 4096 bytes)
OMAP clockevent source: GPTIMER12 at 32768 Hz
Console: colour dummy device 80x30
console [tty0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 128MB = 256MB total
Memory: 242432KB available (4100K code, 723K data, 144K init, 0K highmem)
Calibrating delay loop... 744.68 BogoMIPS (lpj=2908160)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 520 bytes
regulator: core version 0.5
NET: Registered protocol family 16
MUX: setup Y9_3430_USB1HS_PHY_STP (0xd80025d8): 0x001b -> 0x0003
MUX: setup Y8_3430_USB1HS_PHY_CLK (0xd80025da): 0x0013 -> 0x0003
MUX: setup AA14_3430_USB1HS_PHY_DIR (0xd80025ec): 0x0113 -> 0x010b
MUX: setup AA11_3430_USB1HS_PHY_NXT (0xd80025ee): 0x0113 -> 0x010b
MUX: setup W13_3430_USB1HS_PHY_D0 (0xd80025dc): 0x0113 -> 0x010b
MUX: setup W12_3430_USB1HS_PHY_D1 (0xd80025de): 0x0113 -> 0x010b
MUX: setup W11_3430_USB1HS_PHY_D2 (0xd80025e0): 0x0113 -> 0x010b
MUX: setup Y11_3430_USB1HS_PHY_D3 (0xd80025ea): 0x0113 -> 0x010b
MUX: setup W9_3430_USB1HS_PHY_D4 (0xd80025e4): 0x0113 -> 0x010b
MUX: setup Y12_3430_USB1HS_PHY_D5 (0xd80025e6): 0x0113 -> 0x010b
MUX: setup W8_3430_USB1HS_PHY_D6 (0xd80025e8): 0x0113 -> 0x010b
MUX: setup Y13_3430_USB1HS_PHY_D7 (0xd80025e2): 0x0113 -> 0x010b
MUX: setup AA10_3430_USB2HS_PHY_STP (0xd80025f2): 0x0013 -> 0x0003
MUX: setup AA8_3430_USB2HS_PHY_CLK (0xd80025f0): 0x0013 -> 0x0003
MUX: setup AA9_3430_USB2HS_PHY_DIR (0xd80025f4): 0x0113 -> 0x010b
MUX: setup AB11_3430_USB2HS_PHY_NXT (0xd80025f6): 0x0113 -> 0x010b
MUX: setup AB10_3430_USB2HS_PHY_D0 (0xd80025f8): 0x0113 -> 0x010b
MUX: setup AB9_3430_USB2HS_PHY_D1 (0xd80025fa): 0x0113 -> 0x010b
MUX: setup W3_3430_USB2HS_PHY_D2 (0xd80021d4): 0x0113 -> 0x010b
MUX: setup T4_3430_USB2HS_PHY_D3 (0xd80021de): 0x0113 -> 0x010b
MUX: setup T3_3430_USB2HS_PHY_D4 (0xd80021d8): 0x0113 -> 0x010b
MUX: setup R3_3430_USB2HS_PHY_D5 (0xd80021da): 0x0113 -> 0x010b
MUX: setup R4_3430_USB2HS_PHY_D6 (0xd80021dc): 0x0113 -> 0x010b
MUX: setup T2_3430_USB2HS_PHY_D7 (0xd80021d6): 0x0113 -> 0x010b
Found NAND on CS0
Registering NAND on CS0
OMAP DMA hardware revision 4.0
bio: create slab at 0
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
beagle_twl_gpio_setup:255
MUX: setup M4_34XX_GPIO35 (0xd800207c): 0x0000 -> 0x011c
twl4030_mmc_init:354
twl4030_mmc_init:369
twl4030_mmc_init:369
MUX: setup AE2_3430_MMC2_CLK (0xd8002158): 0x011c -> 0x0100
MUX: setup AG5_3430_MMC2_CMD (0xd800215a): 0x011c -> 0x0118
MUX: setup AH5_3430_MMC2_DAT0 (0xd800215c): 0x011c -> 0x0118
MUX: setup AH4_3430_MMC2_DAT1 (0xd800215e): 0x011c -> 0x0118
MUX: setup AG4_3430_MMC2_DAT2 (0xd8002160): 0x011c -> 0x0118
MUX: setup AF4_3430_MMC2_DAT3 (0xd8002162): 0x011c -> 0x0118
MUX: setup AF10_3430_MMC3_CLK (0xd80025d8): 0x0003 -> 0x011a
MUX: setup AC3_3430_MMC3_CMD (0xd80021d0): 0x0008 -> 0x011b
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VUSB1V5: 1500 <--> 0 mV normal standby
regulator: VUSB1V8: 1800 <--> 0 mV normal standby
regulator: VUSB3V1: 3100 <--> 0 mV normal standby
regulator: VPLL2: 1800 mV normal standby
regulator: VSIM: 1800 <--> 3000 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
SCSI subsystem initialized
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
musb_hdrc: USB OTG mode controller at d80ab000 using DMA, IRQ 92
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
omap-iommu omap-iommu.1: isp registered
omap-iommu omap-iommu.2: iva2 registered
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 473
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler cfq registered (default)
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
loop: module loaded
usbcore: registered new interface driver cdc_ether
Linux video capture interface: v2.00
omap-iommu omap-iommu.1: isp: version 1.1
failed omapvout register/probe -19
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
i2c /dev entries driver
Driver 'sd' needs updating - please use bus_type methods
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-b)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand":
0x000000000000-0x000000080000 : "X-Loader"
0x000000080000-0x000000260000 : "U-Boot"
0x000000260000-0x000000280000 : "U-Boot Env"
0x000000280000-0x000000680000 : "Kernel"
0x000000680000-0x000010000000 : "File System"
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OMAP-EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.29-omap1-00048-ge749c1f ehci_hcd
usb usb1: SerialNumber: ehci-omap.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC b2:66:f6:37:40:42
usb0: HOST MAC 66:a6:d4:0a:a6:ae
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: MUSB HDRC host driver
usb usb2: Manufacturer: Linux 2.6.29-omap1-00048-ge749c1f musb-hcd
usb usb2: SerialNumber: musb_hdrc
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mice: PS/2 mouse device common for all mice
OMAP Keypad Driver
twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
twl4030_rtc twl4030_rtc: Power up reset detected.
twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC.
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
regulator: Unable to get requested regulator: vmmc
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
kbde: loaded
Advanced Linux Sound Architecture Driver Version 1.0.18a.
input: AT Translated Set 2 keyboard as /devices/serio0/input/input0
No device for DAI twl4030
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
OMAP3 Beagle/Devkit8000 SoC init
TWL4030 Audio Codec init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
usb 1-2: new high speed USB device using ehci-omap and address 2
ALSA device list:
#0: omap3beagle (twl4030)
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
lib80211: common routines for IEEE802.11 drivers
Power Management for TI OMAP3.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
fbcvt: 1024x768@60: CVT Name - .786M3-R
FIXME: no omap_set_dma_color_mode on 24xx
DMA transaction error with device 0
Console: switching to colour frame buffer device 128x48
twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 UTC (94668)
Waiting for root device /dev/mmcblk0p2...
usb 1-2: New USB device found, idVendor=05e3, idProduct=0608
usb 1-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-2: Product: USB2.0 Hub
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
mmc0: new SD card at address e5c6
mmcblk0: mmc0:e5c6 SU01G 968 MiB
mmcblk0: p1 p2 p3
usb 1-2.1: new low speed USB device using ehci-omap and address 3
usb 1-2.1: New USB device found, idVendor=054c, idProduct=01a9
usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2.1: Product: FKP-U01
usb 1-2.1: Manufacturer: Sony
usb 1-2.1: configuration #1 chosen from 1 choice
input: Sony FKP-U01 as /devices/platform/ehci-omap.0/usb1/1-2/1-2.1/1-2.1:1.0/i1
generic-usb 0003:054C:01A9.0001: input: USB HID v1.11 Keyboard [Sony FKP-U01] o0
input: Sony FKP-U01 as /devices/platform/ehci-omap.0/usb1/1-2/1-2.1/1-2.1:1.1/i2
generic-usb 0003:054C:01A9.0002: input: USB HID v1.11 Mouse [Sony FKP-U01] on u1
usb 1-2.2: new low speed USB device using ehci-omap and address 4
usb 1-2.2: New USB device found, idVendor=093a, idProduct=2510
usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2.2: Product: USB OPTICAL MOUSE
usb 1-2.2: Manufacturer: PIXART
usb 1-2.2: configuration #1 chosen from 1 choice
input: PIXART USB OPTICAL MOUSE as /devices/platform/ehci-omap.0/usb1/1-2/1-2.23
generic-usb 0003:093A:2510.0003: input: USB HID v1.11 Mouse [PIXART USB OPTICAL0
usb 1-2.4: new high speed USB device using ehci-omap and address 5
kjournald starting. Commit interval 5 seconds
usb 1-2.4: New USB device found, idVendor=056e, idProduct=7001
usb 1-2.4: New USB device strings: Mfr=16, Product=96, SerialNumber=0
usb 1-2.4: Product: USB2.0 PC Camera
usb 1-2.4: Manufacturer: PixArt Imaging Inc.
usb 1-2.4: configuration #1 chosen from 1 choice
EXT3 FS on mmcblk0p2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) on device 179:2.
Freeing init memory: 144K
uvcvideo: Found UVC 1.00 device USB2.0 PC Camera (056e:7001)
input: USB2.0 PC Camera as /devices/platform/ehci-omap.0/usb1/1-2/1-2.4/1-2.4:14
input: Fake Touchscreen as /devices/virtual/input/input5
# warning: `rild' uses 32-bit capabilities (legacy support in use)